Floor drain repair service

Trust our team to fix your drain floor drain

The bathroom and other rooms should look aesthetically pleasing and modern; therefore, and also because it is safer and more convenient, the option of laying sewer pipes inside the floor was invented, which in turn requires the installation of a trap. But this does not eliminate the problems that can arise with a drain in the floor. What can go wrong, and what actions should be taken to prevent damage to the house and flooding of the premises?

• If you notice an unpleasant smell, the trap may be the cause. And be careful, because, in addition to the smell, insects can also enter. In this case, simply pour the water down the drain;
• It will be more difficult if you find a blocked drain. In this case, you need to act based on the type of problem. For example, if the hair clogged the drain, then you can use a drainage snaking, but if it is an accumulation of fat or soap, then it is better to trust professionals who will quickly and efficiently perform the necessary work;
• If water returns from the drain hole, this may be since the plumbing system provides for relieving the main drain pipe of a lot of pressure. But in the case when there is no little overflow, this may indicate that there is a leak somewhere in the system. Our specialists will check the entire system to find the leak and will eliminate it.
• Well, the worst scenario is when water pours out of the trap and floods the room. The reason for this could be heavy rain and an increase in groundwater if we are talking about a basement or other problems that can cause sewer water to enter your bathroom. Then you need to call plumbers urgently.

Repair of drain pipes inside the floor must be carried out in a certain sequence and after careful preparation. Only in this case the result of the work will meet expectations, and the installed system will be distinguished by reliability and high efficiency. Therefore, it is better to turn to qualified plumbers for this matter.

Our company, Superior Plumbing & Heating, brings together everything you need to install and repair your home’s floor drain. We perform emergency work instantly and regularly service the system to prevent problems in the future. If you are looking for floor drain repair, then we guarantee you that we will not leave you alone with the problem that has arisen.

How to perform basement floor drain replacement?

Let’s start with what to do if your basement drain is clogged and you find standing water there. Breakdown of the basement floor drain is a disaster for residents; it often leads to flooding of the basement. This can happen due to cracks and holes in the drain. Also, a breakthrough can often be caused by the use of poor-quality pipes or violations during installation. And over time, sealing gaskets can wear out. This happens with old sewer systems that have not been changed or repaired for a long time.

If such a problem is found, it must be urgently addressed. Of course, the most important recommendation would be to call a specialist who knows how to replace the drain in the basement. Contacting a professional will help you make sure that the work is done well, and a similar problem will no longer take you by surprise. You can also use the following tips:

• For basement floor drain replacement, the old drain must first be removed. To do this, break the concrete around to get to the old drain;
• Next, you need to install new drainage pipes. The most important thing is to observe the correct slope for the successful operation of the drain;
• Keep in mind that the trap on the basement floor must be very secure. After installing the drain cap, the place where you broke the old concrete must be filled with a new layer and wait until it hardens.

If you are not confident in your abilities or do not know how to do all the work correctly, then the best solution is to call the qualified masters of Superior Plumbing & Heating. We will replace the drain in the basement quickly, efficiently, and at an affordable price, thereby saving you from dirty work and the need to spend money on repeated repairs.

What to do if the drain is clogged?

There’s nothing worse than going into the bathroom after a day’s work to take a shower only to find that the water won’t drain. Having a clogged drain is an unpleasant thing that we unfortunately have to deal with. But before we deal with the ways to eliminate them, let’s talk about what can provoke them. This may be due to:

• Getting hair and threads from clothes into the drain this problem occurs especially quickly, provided that there are owners of long hair in the house;
• Often the owners do not notice small debris of any kind; the ingress of solid debris significantly worsens the situation;
• Fat deposits on the inner walls of the pipes;
• Accumulations of dirt along with soap residue;
• Problems with the sewer system at home.

It should be noted that even despite various preventive measures, the problem of blockage may occur. There are several methods to fix it:

• With vinegar and soda. This method is suitable for those cases when the pollution of the drain hole has just arisen and is not strong. It is required to mix these products in equal proportions and add them to the drain. After 60 minutes, rinse the hole with the strong pressure of hot water;
• With the help of specialized cleaning products. More suitable for preventive work, like the first method. With large pollution in the form of large mud clods, chemical preparations will not be able to cope.
• For more serious blockages, if water does not drain in the shower, a plunger will be a good way to deal with blockages. The first step is to draw water to cover the device’s rubber head. The drain must be completely closed with a plunger installed at a slight inclination. Thus, the drain hole will not be cleaned with air but collected water. After making 20-25 up and down movements, rinse the drain using hot water.5

What is drain snaking and how does it help clear blockages?

When there is a problem of a clogged or slow drain, in addition to all of the above, one of the ways to solve this problem is to use a drain snaking. Let’s take a moment to learn more about why this can be useful and when it should be used.

The drainage snake is a metal cable, up to 25 feet long, wound around a protective drum. Not everyone has this device at home, and you need the necessary knowledge to use it. Therefore, in such a case, it is better to trust the master. A spring, designed to remove blockages, is at the end of the cable. The master pushes the cable, unwinding it from the drum and moving it along the pipe. The drum locks into place when it hits an obstacle, allowing the cable to turn. Then the sharp end clings to the obstacle and holds it, after which the master pulls it in the opposite direction and thus gets rid of the blockage. This method helps to remove hard-to-reach debris easily. The cable must be used very carefully to prevent damage to the drain system. After, it is necessary to shed the drain with the strong pressure of high-temperature water.

Drain snaking is one of the most common and effective wastewater treatment services. And our company, Superior Plumbing & Heating, is happy to provide it to you, safely and effectively cleaning the drain and restoring your peace of mind.

How to install a floor drain trap?

Shower cabins with a steel or plastic pallet do not always meet users’ requirements. Often the foundations are made of stone or concrete. In this case, to drain the water, you will need to install a trap. Its main purpose is to collect water from the pan and drain it from the shower. Thanks to the design of the product:

• Water is filtered from debris, preventing it from entering the outlet pipes;
• An unpleasant odour is prevented from coming from the general house sewer risers;
• Sealing of the docking drain zone is provided.

In addition, due to simple disassembly, access for maintenance and cleaning of sewer pipes is facilitated. Large debris is retained by the grate, while small debris settles in the external discharge channel. If you remove the grille, you can easily clean the internal parts from small particles.

Complex drains are complemented by filter grilles, flanges that provide a secure fastening, and sealing rings. Such a device eliminates leakage and flooding of neighbours from the lower apartments. For floor drain trap installation, you need to do the following:

• Determine the place where the trap will be located;
• Connect the trap to the sewer drain;
• Pour concrete mortar over;
• Make a gasket for the flange;
• Lay the upper part of the flange on the gasket and screw it to the lower part;
• Cover the screed with a layer of waterproofing;
• Insert its inner part into the body of the trap.

Whatever type you have, the process of its installation should be entrusted to a qualified master. This is a very responsible process that requires certain knowledge and skills. The masters of Superior Plumbing & Heating will not only perform a quality installation but will also tell you what drains your shower enclosure needs. We will perform work of any complexity with high quality and with a guarantee!

What about installing a drain inside a concrete floor?

Today, bathrooms with a drain inside the floor are popular. Perhaps this is a trend of minimalist fashion, or maybe a desire to save money. It is very convenient and practical. The drain in the bathroom floor performs several important functions for the shower, which provide water drainage, prevent the accumulation of moisture, the development of pathogenic microflora, and the presence of unpleasant odours. It also ensures against damage to neighbouring property during plumbing problems. To make a drain inside the floor, you need:

• Drain housing, including outlets;
• Clamping flanges for connecting pipes;
• Seal;
• Siphon;
• Lattice;
• Perforated metal glass — an additional filter.

When installing a drain, you must adhere to strict rules. You need to choose a place for draining:

• In the center of the bathroom. In this case, the slope must be done either on 4 sides or 2 sides.
• Near the wall. The slope is on one side.

At the stage of installing the floor, a tube is installed that provides a drain.

Let’s figure out how to install a floor drain in concrete. It begins with the laying of the sewer pipe. The slope should be no more than 3 cm; the trap should go into the pipe. Next, a siphon is attached to it, and the trap body is installed under the drainage system. In this case, it is impossible to tilt the pipe too much since an excessive slope can subsequently provoke a breakdown of water in the siphon. After this, the surface is usually waterproofed, a concrete screed is poured, and tiles are laid.

If the installation recommendations are followed, the floor surface maintains the desired slope, and the use of the drain is safe. By following all the stages of installation, you will not only extend the life of the product itself but also increase the maintenance-free period of the shower room.

Installing a drain in the floor has its nuances and subtleties, so it is better to trust this work to experienced plumbers. Ask for help from our qualified specialists, they will suggest the best option for your bathroom and perform a competent installation. Your comfort is our job!